Maximum availability before and after sale. To check compatibility, send a few copies of the booklet. For cars registered after 1 November 2014 it is advisable to check the presence of a tpms valve for the control of the pressure on the rim, consult for more information. Finally, tpms sensors are sold separately and encoded with new identification codes.
Contact us before you buy to check the actual availability of the desired quantity. Specify the type of car in the notes at the time of purchase: make/model/cylinder/year of registration, to check compatibility with your car. We are a company that has been operating in the sector for more than 50 years. We have a wide range of matching tires, great offers for winter tires.
For those who buy wheels and complete tires, everything happens directly to you assembled and balanced, ready to be mounted under the car without any assistance. Channel width - 7.5d rim diameter - 17 brand - aftermarket quantity - 4 holes - 5 offset - 45 mm hole distance / pcd - 112 material - aluminium ean - 5x112-17-45-lookmap cb - 66,5.How to read a tire interpretation of tire information: to know all the basic information about a tire, just read the information below 1 balancing the tires of unbalanced tires cause vibration, which in turn can lead to fatigue of the driver and premature and uneven wear of the tires as well as wear of the suspension of the vehicle. Tyres shall be balanced at the time of installation or when repositioning after maintenance. The balance of the tyres must be checked as soon as the first signs of vibration appear. 2 tire pressure it is very important to check the tire pressure at least once a month using a pressure gauge. Incorrect inflation can cause abnormal and excessive wear and laceration, which in turn can lead to overheating of the tire, excessive fuel consumption or even a burst of the tire itself.
Make sure you check the pressure when the tires are cold and have not been used recently. Even if you drive only one kilometer, the tire pressure increases and therefore a correct measurement is altered. A continuous loss of inflation pressure indicates a potential tyre or wheel assembly problem. If this is the case, contact a tire dealer immediately. 3 tire repair tires must be repaired by specialized tire dealers.
The correct repair procedure is to remove the tire from the rim, so that you can check the damage, and apply the fungus as well as the anti-puncture patch that falls within the limits of the repair instructions. 4 tyre rotation although many are able to switch their tires on their own, the best, fastest and safest way to do so is to trust professionals. The correct procedure and schedule for permuting tyres are described in the vehicle manual.If no schedule is indicated, it is recommended to rotate every 8,000 to 10,000 kilometres. 5 wheel alignment it can be said that a vehicle is correctly aligned when all steering and suspension components are properly fixed and the tires and wheels are properly arranged. If you notice uneven tread wear, it is possible that the wheels are misaligned and, therefore, it is necessary to consult a specialist technician. Tire type defines the intended use of the tire. P (united states only) indicates that it is a passenger car tire. Lt (united states only) indicates that it is a truck tire. Tyre width measured in millimetres from side to side. The width of this tire is 215 mm. Aspect ratio percentage ratio between tyre section height and width. 65 indicates that the height is 65 per cent of the tyre width. Construction this indication specifies how the tire was assembled. The r indicates that it is a radial tire. These layers of textile yarn form the very structure of the tyre and are arranged radially from one fillet to the other. The b indicates that the tire has a cross-folded structure, which means that the threads of the folds extend diagonally along the rod-ring tire, the fibre layers being arranged in alternating directions for greater reinforcement. Wheel diameter the width of the wheel from end to end. The wheel diameter is 15 inches. Load index indicates the maximum load that a tire can withstand when inflated. The maximum load in pounds and kilograms is also indicated elsewhere on the sidewall of the tyre. Speed category indicates the maximum speed of use of a tire.
H indicates that the tyre has a maximum operating speed of 210 km/h. These data relate only to tyre speed and do not constitute an invitation to exceed the speed limits established by law; it is recommended to always drive within speed limits. Point indicates that the tire complies with the safety regulations of the United States Department of Transport. Next to this indication is a tire identification or a serial number consisting of an alphanumeric combination of up to 12 characters. Utqg is the abbreviation of "uniform tire quality graduation", a quality assessment system developed by the U.For more information on utqg, see the page "notation utqg". Tire maintenance tips: 1 check the tread of the tire regularly check the tread of your tires to decide if you need to replace them. All tyres for passenger cars, light commercial vehicles and medium-sized vehicles have wear indicators integrated into the tread. These indicators are located at the base of the tread grooves, at different positions along the tire. When the tread residue reaches the level of the adjacent tread veins, the tyre has a wear stage such that it is necessary to replace it.
If the tread wear is only pronounced at one or two locations, this means that the tire has not been inflated properly. Here are some of the most common signs of uneven tread wear and their causes: 1.1 tread blocks and grooves: worn parts curvature is more common in front tires, but can also occur in rear tires. This may indicate that the wheels are not properly balanced or that the suspension or certain components of the steering system of the car are worn out. 1.2 Saw Teeth Edge: Disalignment Do the tread edges appear to be saw teeth or otherwise worn? This is due to an inappropriate slip on the road surface.
To solve the problem, it is necessary to adjust the convergence of the car. A correct tread depth is essential to ensure correct tyre performance. If you notice a difference or loss of traction on wet ground, there may not be enough residual tread left on the tires. When the sculpture depth is reduced to 1.6 mm, the tire must be replaced.
1.3 centre wear: overpressure if a tire has been too inflated, the centre of the tread supports most of the load and is used more quickly than the side edges. Unequal wear reduces the useful life of a tire. Excessive tire wear may also be due to misalignment or mechanical problems.
1.4 wear on both sides: insufficient pressure if the tire looks like this, it may not have been inflated enough. Insufficient pressure reduces the life of the tread due to increased wear on the outside (or shoulders) of the tire.
This condition also causes excess heat, which shortens the life of the tire. Finally, there is also a higher fuel consumption due to increased rolling resistance (soft tires are more demanding of the vehicle). 2 balancing of the tires of unbalanced tires causes vibrations, which in turn can lead to fatigue of the driver and premature and uneven wear of the tires as well as wear of the suspension of the vehicle. 3 tire pressure it is very important to check the tire pressure at least once a month using a pressure gauge. 4 tire repair tires must be repaired by specialized tire dealers.
5 Tire rotation although many are able to switch their tires on their own, the best, fastest and safest way to do so is to trust professionals. 6 wheel alignment it can be said that a vehicle is correctly aligned when all steering and suspension components are properly fixed and the tires and wheels are properly arranged. Instructions for the assembly of the rims general indications the applications mentioned in the technical catalogue are simply indicative, given the speed and continuity of evolution of the various components brake calipers, steering geometry, mudguards, shock absorbers, etc. Tire assembly ensure that the wheel does not need to be mounted upside down use tires proportionate to the width of the alloy rim. Use tires, even lowered tires, proportionate to the originals.
Attach the wheel to the car tighten the screws/nuts in reverse or cross-order. Respect scrupulously the instructions given in the "remarks" and/or "warnings" section of the technical catalog for the car you want to equip.Check that all screws/nuts have the same coupling as the wheel, i. Spherical with spherical (with the same radius) and conical with conical. The torque of the screws or nuts on the plate of the car shall be carried out strictly as indicated by the vehicle manufacturer or, alternatively and if present, following the instructions of the documents accompanying the set of wheels. Check the clamping torque again after 500 km.
The correct screwing between the nuts and bolts, the wheel and the car is completed if the number of turns to be made by the nut/ screw for full clamping is equal to or greater than 6, regardless of the bolt step. Check that the original key provided with the car is compatible with the screwdriver provided with the wheel. Shocks the material used for the construction of alloy wheels is a particular aluminum-¬ silicon alloy with excellent elongation characteristics.In the event of a violent impact, the tyre shall be disassembled to verify any damage sustained. Check that the eccentricity of the wheel has remained within the permitted 0.50 mm; b the presence of any folds which may give rise to leaks of air or, in the most serious cases, to the initiation of breakages.
Any type of intervention (mechanical or otherwise) to restore wheel integrity is strictly prohibited and excludes warranty rights. Maintenance and maintenance of Wheel 1 to maintain the radiance and colour of the wheels, follow these regular cleaning rules: never wash the wheels when they are hot. Washing hot wheels could seriously damage the painted surface of your new wheels. 2 the dirt and brake dust that accumulate on the surface of the wheels must be removed weekly by washing the wheels with warm water and mild soap with a soft sponge. The dust on the road holds the moisture and this could damage the painted surface if it is left for a long time.The brake dust is very corrosive and abrasive and could damage the painted surface of the wheel. 3 the wheels must be dried after washing, using a soft cloth. 4 never use abrasive sponges or steel wool. 5 never use tire cleaners, they contain chemicals harmful to the surface of the wheels.
If you wash your car in an automatic car wash, make sure first that no chemical is used that could damage the finishing of the wheels. 6 if a specific detergent for alloy rims is used (it must be of neutral ph and diluted in water) never allow it to act on the rim for more than two minutes.
Rinse the wheel immediately with water. Never use acidic or alkaline cleaners, solvents, diluents, petroleum, naphtha. Diesel, petrol, benzene, kerosene, methyl alcohol, hydraulic oil. Shipping by courier according to the area and type of goods (sda, gls, brt and others).
We personally guarantee the goods shipped: if they arrive damaged or lost, we immediately send a new package or proceed with the refund when a replacement is not available. For goods damaged during transport, it is essential to accept delivery with reservation.
The goods are delivered to the carrier on the same business day as you made the purchase, for payments credited before 1:00 p., unless the goods are not available. Delivery time 2-4 working days. Regularly check the tread of your tires to decide if you need to replace them. Here are some of the most common signs of uneven wear of the tread.
The item "Alloy wheels for mercedes from 17 5x112 look map and 45 class a b c" is on sale since Tuesday 31 March 2020. It is in the category "auto, motorcycle - parts, accessories\auto\ tires, rims\ rims". The seller is "ruote-gommaspeed" and is located in/in ischia.
This item may be shipped to the following country: europe.